此语言仍有 24 条内容或界面任务待翻译;未完成部分显示中文原文。
Robotic Arm Z1Category Diagram
Content Correction
Brand 宇树科技

Robotic Arm Z1

Model Z1 AIR / Z1 PROEmbodied AI Robot Core Components
关键规格 1Provided by Supplier自由度6轴
关键规格 2Provided by Supplier负载2kg(Z1 AIR)/≥3kg(Z1 PRO)
关键规格 3Provided by Supplier最大臂展740mm
关键规格 4Provided by Supplier重复定位精度约0.1mm
Reference unit priceRequest a Quote

Reference subtotal Request a Quote

价格与库存供选型参考,正式报价和交期请供方确认。

Specification Parameters

Processor & Control

Control Frequency
1KHz · High-speed communication via 485
Control Interface
位置+力控 · Supports force feedback and collision detection
Encoder Resolution
15bit · Joint parameter

Storage & Transmission

Reducer
谐波减速器 · Gear ratio 60+, bearings are industrial-grade crossed roller

Interfaces & System

System Interface
Ethernet · Both Z1 AIR and Z1 PRO use Ethernet
User Control System
Ubuntu · Same for both versions
Communication Method
高速485 · Joint communication

Power Supply

Voltage
24V · Power requirements: voltage 24V, current >20A; motor recommended at 24V
Power
峰值500W · Peak rating

Body Specifications

Degrees of Freedom
6轴 · Z1 AIR is identical to Z1 PRO
Self-Weight
4.3kg(Z1 AIR)/ 4.5kg(Z1 PRO) · Total robot weight
Payload
2kg(Z1 AIR)/ ≥3kg(Z1 PRO) · Rated payload
Maximum Reach
740mm · Same for both versions
Repeatability
约0.1mm · Determined by actual usage test requirements

Joint Specifications

Maximum Torque
33N·m · Joint specifications
Backlash
约6弧分 · Joint specifications
Force Control Accuracy
约0.2N·m · Joint specifications
Maximum Joint Speed
180°/s · Both J1–J6 are 180°/s
Range of Motion
J1 ±150°、J2 0-180°、J3 -165°-0、J4 ±80°、J5 ±85°、J6 ±160° · Range of motion for each joint

Joint Module

Dimensions
Φ65*52mm · Joint module dimensions
Weight
405g · Joint module weight

Interfaces and Dimensions

Joint module dimensions
Φ65*52mm
Maximum reach
740mm
Total robot weight
4.3kg(Z1 AIR)/ 4.5kg(Z1 PRO)

Comparison with Similar Products

Specifications本品 · Z1 AIR / Z1 PRORMG22-65BT2-05(标准)/ BT2-06(长续航)仿人型智能灵巧手DH116
Main controller—————
NPU—————
Memory / VRAM—————
Reference unit priceRequest a QuoteRequest a QuoteRequest a QuoteRequest a QuoteRequest a Quote
Inventory—————

Product introduction

In terms of specifications, Z1 is offered in two models: Z1 AIR and Z1 PRO: both have 6 degrees of freedom, weigh 4.3kg and 4.5kg respectively, with payloads of 2kg and ≥3kg, a maximum reach of 740mm, and repeat positioning accuracy of approximately 0.1mm (officially noted that this depends on testing under actual use conditions, as testing standards vary widely). Interfaces and system: communication is via high-speed 485, the external interface of the unit is Ethernet, the user control system is Ubuntu, and the control interface is position + force control, with force feedback and collision detection. Joint parameters: maximum torque 33N·m, backlash of approximately 6 arcminutes, encoder resolution 15bit, force control accuracy of approximately 0.2N·m, control frequency 1kHz, using harmonic drives and industrial-grade crossed roller bearings, with a reduction ratio of 60+, maximum single-joint speed of 180°/s, and motor sensing feedback and control commands covering torque, angle, angular velocity, as well as stiffness and damping. Power supply: recommended voltage 24V; the unit's power requirements are voltage 24V, current >20A, with peak power of 500W. Mechanical dimensions (joint module): Φ65*52mm, weight 405g. Compatibility and integration: officially stated to work with Aliengo, B1, and other quadruped and mobile robots to accomplish complex tasks collaboratively; the end-effector can be swapped with different actuators, and the robotic arm's control programs and control interfaces will be progressively open-sourced. Delivery and usage restrictions: this product is a consumer robotics product; the official reminder is to avoid hazardous modifications and usage, and to comply with laws and regulations in each region.

Sources 宇树科技

Compilation Notes 内容由 AI 根据公开资料整理;事实与推断分开呈现。

Content Correction

Product parameter comparison

Product Selection Assistant

让需求变成可修改的筛选条件

依据已录入参数生成条件,结果可查看和修改。帧率与性能需核对实测,不能仅凭算力数值保证。