Specification Parameters
Processor
- Processor
- 32 位 RISC-V 单核处理器,最高 160 MHz · ESP32-C3 SoC
Memory
- ROM
- 384 KB · SoC feature
- SRAM
- 400 KB(其中 16 KB 用作缓存) · SoC feature
- RTC SRAM
- 8 KB · SoC feature
Interfaces & System
- GPIO
- 22 个可编程 GPIO · SoC feature
- Serial Interfaces
- 3 个 SPI、2 个 UART、1 个 I2C、1 个 I2S · SoC feature
- USB
- 全速 USB Serial/JTAG 控制器 · SoC integrated
- Analog
- 2 个 12 位 SAR ADC,最多 6 个通道;1 个温度传感器 · SoC feature
- I2C Peripherals
- IMU ICM-42670-P(0x68)、温湿度 SHTC3(0x70) · SDA GPIO10, SCL GPIO8
- GPIO Connectivity Devices
- WS2812 LED(GPIO2)、LED(GPIO7)、按键/Boot(GPIO9) · On-board devices
Power Supply
- Power Interface
- USB Type-C(不兼容 PD) · Board power supply
- Battery Charging
- MCP73831T-2ACI/OT 锂离子电池充电器,最高充电电压 4.2 V · No overcurrent or over-discharge protection
Comparison with Similar Products
| Specifications | 本品 · ESP32-C3-DevKit-RUST-1 | RDK S100 | DFR0706-1 | 5G模组/LTE模组/智能模组/Wi-Fi模组/GNSS模组(产品线总览,无具体型号) | DFR1231 |
|---|---|---|---|---|---|
| Main controller | ESP32-C3 | S100 智能计算芯片 | 国产 4核 1.2GHz | — | — |
| NPU | — | 80 TOPS | — | — | — |
| Memory / VRAM | — | 12 GB | 0.5 GB | — | — |
| Reference unit price | Request a Quote | ¥2,799 | ¥619 | Request a Quote | ¥39 |
| Inventory | — | — | — | — | — |
Product introduction
Project specifications: According to official documentation, this development board is based on the ESP32-C3, integrating sensors, LEDs, buttons, a battery charger and a USB Type-C interface. The project provides all materials needed to build the board yourself, including the KiCad project libraries, an interactive BOM, and 3D-printable case models. Processor and memory: The ESP32-C3 is a 32-bit RISC-V single-core processor running at up to 160 MHz, with 384 KB ROM, 400 KB SRAM (of which 16 KB is used as cache), and 8 KB RTC SRAM. Wireless: Compliant with IEEE 802.11 b/g/n, supporting Bluetooth 5 and Bluetooth Mesh. Peripherals: 22 programmable GPIOs, 3 SPI, 2 UART, 1 I2C, 1 I2S, 2 12-bit SAR ADCs (up to 6 channels), temperature sensor, RMT, LEDC, GDMA, TWAI, etc. I2C peripherals: The IMU is the ICM-42670-P (address 0x68), the temperature/humidity sensor is the SHTC3 (address 0x70), with I2C SDA on GPIO10 and SCL on GPIO8. GPIO connections: The WS2812 LED is on GPIO2, the LED is on GPIO7, and the button/Boot is on GPIO9. Power supply: USB Type-C (not PD-compatible), with an on-board MCP73831T-2ACI/OT lithium-ion battery charger, maximum charging voltage 4.2 V; the official recommendation is to use a battery with a protection circuit, and battery voltage reading is not supported. Purchase channels: Espressif's official AliExpress store and Mouser Electronics; orders via Mouser in parts of Europe require export declaration processing. Training materials: Ferrous Systems offers the training book and materials "Explore the power of Rust on the new Espressif board".
